Adaptive feedback control of stability in an axial compressor with circumferential inlet distortion

The adaptive feedback control of stability with circumferential inlet distortion has been experimentally investigated in a low-speed, axial compressor. The flat-baffles with different span heights are used to simulate different distorted inflow cases. Compared with auto-correlation and root-mean-square analysis, cross-correlation analysis used to predict early stall warning does not depend on the distortion position. Hence, the cross-correlation coefficient was used to monitor the stable status of the compressor and provide the feedback signal in the active control strategy when suffering from different distortions. Based on the stall margin improvement of tip air injection obtained under different distorted inflow cases and the sensitivity analysis of cross-correlation coefficients to injected momentum ratios, tip air injection was adopted as the actuator for adaptive feedback control. The digital signal processing controller was designed and applied to achieve adaptive feedback control in distorted inflow conditions. The results show that the adaptive feedback control of air injection nearly achieves the same stall margin improvement as steady air injection under different distortion intensities with a reduced injection mass flow. Thus, the proposed adaptive feedback control method is ideal for the engine operation with circumferential distorted inflow, which frequently occurs in flight.     

Study of aerodynamic and inertial forces of a experimental and numerical methods

The force-generation mechanism of a dovelike flapping-wing micro air vehicle was studied by numerical simulation and experiment. To obtain the real deformation pattern of the flapping wing, the digital image correlation technology was used to measure the dynamic deformation of the wing. The dynamic deformation data were subsequently interpolated and embedded into the CFD solver to account for the aeroelastic effects. The dynamic deformation data were further used to calculate the inertial forces...     

基于PSK调制的数字通信信号仿真分析技术

基于PSK调制的数字通信系统在无线通信工程实践中有着广泛的应用，由于受到各种条件的限制，从实际工程系统接收到的PSK数字通信信号在教学科研中不易获得，而PSK调制仿真数据则可以自己产生。在掌握通信原理和仿真技术的基础上利用Matlab实现对BPSK、DPSK、QPSK、DQPSK、8PSK、π/4-DQPSK、OQPSK等数字通信信号源的模拟仿真，可对调制体制、工作频率、传输码率、采样频率、信道特征等参数进行灵活设置，并按要求生成规定格式的DAT数据文件，可作为调制方式识别软件的训练和测试样本。结合模方谱、平方谱、四次方谱、八次方谱等谱线参数特征，同时结合星座图和眼图进行基于PSK调制的数字通信信号的调制体制判别和验证。     

焊接接头典型缺陷的数字X射线尺寸测量技术

为了准确测量焊接接头典型缺陷的尺寸,提出了一种基于半波高法(HWH)的焊接接头缺陷数字射线尺寸测量技术。首先,分析了数字射线检测系统的调制传递函数(MTF),确定了检测系统的空间分辨率。其次,对焊接接头的典型缺陷进行模拟,通过半波高法测量其尺寸。结果表明:依据瑞利判据,运用双丝像质计测定该检测系统的空间分辨率为4.5 Lp/mm;运用该方法测量焊接接头缺陷尺寸,与实际尺寸基本相符,误差小于6.3%,该方法避免了人为因素的影响,精度可满足日常产品的检测需求。     

A new approach for pulse amplitude measurement using Lagrange’s interpolation for radiation or particle detectors

In radiation detector signal processing, usually, the charge-sensitive preamplifier converts the small charge signal coming from the semiconductor-based detector into voltage form and then the signal is further amplified to measure the energy of the incoming radiation. The voltage pulse from a charge-sensitive preamplifier (CSPA) is amplified using a shaping amplifier which reduces the signal bandwidth. To achieve better energy resolution, precise measurement of the peak amplitude of shaping amplifier output is required. The signal processing methods are available in which the signal from the charge-sensitive preamplifier can be directly digitized using high-speed Analog to Digital Converters (ADC), and then further signal processing such as gain and shaping is carried out inside the Field Programmable Gate Arrays (FPGA). For multiple detector systems, digital signal processing methods are quite difficult to implement in Field Programmable Gate Arrays (FPGA). In this context, The development of an alternative technique is initiated that uses a charge-sensitive preamplifier, shaping amplifier, low sampling analog-to-digital converter, and FPGA, where LaGrange’s interpolation technique is implemented in FPGA to precisely measure the peak of the analog pulse. In this paper, the comparison of the proposed method with other pulse amplitude measurement techniques is discussed. Results show that the implemented technique gives similar energy resolution compared to digital pulse processing and standard peak detector-based techniques.     

基于MBD的框类组件数字化制造方法应用

大型框类组件的制造采用数字化制造方法具有很大优越性,本文论述了将MBD技术应用于框类组件的数字化制造中的方法,给出了框类组件的数字化协调路线以及MBD环境下的数字标工建立方法及应用方法,对提高大型框类组件的制造技术水平并显著缩短制造周期具有重要现实意义。     

ASD规范和数字化客户服务产品定义

简要介绍了欧洲宇航和防务工业协会ASD(Aerospace and Defence Industries Association of Europe)系列标准以及在数字化客户服务产品定义中的应用.